EP#134: Injection Molded Enclosure Design with John Teel

EP#134: Injection Molded Enclosure Design with John Teel

  • John Teel
  • Injection Molding Enclosure Design
    • What is the general process of injection molding?
    • Challenges of Injection Molding: Why does it have this “mystic” aura around it?
    • Designing enclosures for injection molding?
      • Difference between designing for 3D printing and Injection molding
      • What should you look for if you need to get a design done correctly
      • What files will I need to have created?
      • Do I design the mold or does someone else?
    • Design is done. Who do I look for to get my design built?
      • What questions should I have answered before contacting someone?
      • Who do I talk to to get it done?
      • How do I find a manufacturer locally or overseas?
      • Who owns the mold?
      • Should I go with a more expensive/larger mold or cheaper/smaller?
      • How much should I be prepared to spend?
    • Prototyping
      • TL;DR for prototyping an injection molded enclosure
      • What if I want a sample?
      • How do I pick the right material?

Tags: electronics podcast, injection molding, John Teel, MacroFab, macrofab engineering podcast, MEP, Predictable Designs

Jaksot(448)

EP#116: Standard-ish

EP#116: Standard-ish

StephenUsing an oscilloscope as a dynamic signal analyzerAnalog scopesParkerGameboy update Code compiles! Quartus II still compiled my Gameboy Project1.25mm? pitch 21 pin. Connectors are hard to find....

18 Huhti 201852min

EP#115: From A Current Perspective

EP#115: From A Current Perspective

StephenLM13700Dual Operational Transconductance Amplifiers With Linearizing Diodes and Buffers built by Ti?All passive filterNot just a zero ohm resistor ;)Shift the phaseFixing a Kegerator Kegerator ...

12 Huhti 201847min

EP#114: Chasing Oscillations

EP#114: Chasing Oscillations

StephenNasty Analog Oscillations Opamps are drama queens of electronicsSolved the oscillation with a small capacitor in the feedback loop to lower the frequency of the feedbackParkerWaiting on circuit...

4 Huhti 201845min

EP#113: Put All Your Power On Blue

EP#113: Put All Your Power On Blue

StephenAutoDesk Fusion 360Fusion 360 Tutorial by Lars ChristensenParkerGetting the PCM5122 DAC to talk to an ArduinoanalogRead FAST Cuts the number of cycles needed to do an Analog read on the Arduino...

28 Maalis 20181h 1min

EP#112: Bruce Hamby and Owning Your Product

EP#112: Bruce Hamby and Owning Your Product

Bruce HambyAttorney with the Hamby Law FirmThe Hamby Law Firm focuses on patents, intellectual property, trademarks and business lawHas been an attorney in the Houston region for over 15 yearsOwn your...

21 Maalis 201857min

EP#111: Logic Commander

EP#111: Logic Commander

Stephen"Slow Start" or soft start circuitsBulk capacitance is killing the power supply for the new synth designCapacitance MultiplierParkerBadge Design for DefCon NFC Belt BuckleLots of LEDs of course...

14 Maalis 201839min

EP#110: Dangling Transformers

EP#110: Dangling Transformers

StephenRibbon Microphone Turn it into a Hackaday.io project?Make a USB microphone from scratch? PCM2912ATalked about this IC on a previous episode of the MEPDatasheetStephen will be in Denver next wee...

7 Maalis 201838min

EP#109: Arduino, The Gateway Drug To #BadgeLife

EP#109: Arduino, The Gateway Drug To #BadgeLife

AND!XORCheck out the previous MEP EP#69 Incognito Mode for the last time the AND!XOR group was on the podcastBitstr3mDid the Android mobile application for the DEFCON 25 badgeZappDoes the hardware des...

1 Maalis 201848min

Suosittua kategoriassa Tiede

tiedekulma-podcast
rss-mita-tulisi-tietaa
rss-poliisin-mieli
docemilia
rss-duodecim-lehti
utelias-mieli
radio-antro
filocast-filosofian-perusteet
rss-laakaripodi
rss-sosiopodi
ihanat-ipanat
sotataidon-ytimessa
mielipaivakirja
rss-bios-podcast
rss-radplus
rss-opeklubi
rss-lihavuudesta-podcast