EP#145: The Vox in a Box Roxs
Circuit Break - A MacroFab Podcast6 Nov 2018

EP#145: The Vox in a Box Roxs

  • Stephen's Vox in a Box
    • Preamp Design
      • Vox AC30 preamp - 3 gain stages with a cathode follower and a phase inverter
      • Phase inverter - create differential signals for the power amp input
      • Drop signal using voltage dividers and mosfet buffers
      • 320V phase inverter to 18V buffer drive
      • Built point to point on an aluminum plate for easy modification and testing
    • Power Amp Design
      • TPA3116 Class D amplifier
      • LM311 comparator mute circuit for start up mute ~5 to 10 Seconds
      • Runs at 400KHz - Left open pads for boosting this up to 1.2MHz
        • Is there an advantage at running at higher frequencies?
    • Power Supply Design
      • TPS40210 Switching controller into a diode/cap ladder voltage multiplier
      • 7 stages of multiplication leads to ~50V per stage
      • Variable Switching from 35KHz to 1000KHz
      • PMP8621 Appnote
    • Testing the Vox in a Box
      • Been going nonstop for weeks now
      • Have taken it up to nearly 60 Watts without problems
    • Layout of the PCB
      • Multiple ground system with master start
      • Each sub circuit has its own ground return
      • 8 Master star ground returns
      • 4 layers
    • Issues with the current design
      • High Voltage SMPS does not like high capacitive load
      • Ground for signal input is very important - Nearly all noise is dominated by this single point
        • Alligator clips for signal patching are not low noise…
      • Cold Heater impedance
    • Current Schematic for the Vox in a Box
    • Fusion 360
      • New amp design
        • Learning by building a virtual amp
      • Vox in a box
        • Going to model the whole design to ensure proper fit
  • R.F.O.

Tags: Chris Gammel, electronics podcast, Fusion 360, Hackaday, LM311, MacroFab, macrofab engineering podcast, MEP, PMP8621, Preamp, SuperCon, TPA3116, TPS40210, Vox AC30, Vox in a Box

Episoder(448)

EP#412: Great Classes, Odd Teachers, Chickens, Snakes

EP#412: Great Classes, Odd Teachers, Chickens, Snakes

A recent Circuit Break Community thread about K-map design inspired a tangential conversation about how well certain subjects are taught in college. Parker and Stephen love a good tangent, thank you, ...

9 Jan 202450min

EP#411: Entropy rules everything with James Lewis

EP#411: Entropy rules everything with James Lewis

This week Parker and Stephen welcome James Lewis back to the show after a rather long absence! The occasion stems from James chiming in on a Circuit Break Community thread that Stephen started, asking...

2 Jan 20241h 1min

EP#410: Eighth Annual MacroFab Star Wars Christmas Special - Somehow this Podcast Returned

EP#410: Eighth Annual MacroFab Star Wars Christmas Special - Somehow this Podcast Returned

Not unlike Han Solo emerging from cryosleep, the annual MacroFab Star Wars Christmas Special is back! Parker and Stephen welcome Josh Rozier, Chris Kraft, and Hyr0n to Circuit Break for a wide-ranging...

26 Des 20232h 46min

EP#409: You Down with SDV

EP#409: You Down with SDV

Parker and Stephen discuss a recent news story about how car manufacturers are increasing their focus on Software-Defined Vehicles (SDVs) which are cars that use more software instead of physical comp...

19 Des 202354min

EP#408: Pete Staples from Blue Clover on the PLT, Device Testing, more!

EP#408: Pete Staples from Blue Clover on the PLT, Device Testing, more!

Parker and Stephen welcome Pete Staples, the CEO and Co-Founder of Blue Clover Devices, to the show! Staples founded Blue Clover in 2003 to explore ways to make the electronics industry more efficient...

12 Des 202356min

EP#407: Holy Static Hazard Batman!

EP#407: Holy Static Hazard Batman!

Parker and Stephen discuss a recent article exploring how electrostatic discharge damage isn’t the only kind of static hazard your digital designs can face and possible solutions to such problems, a r...

5 Des 202356min

EP#406: Dr. Duncan Haldane from JITX on Automating Circuit Design

EP#406: Dr. Duncan Haldane from JITX on Automating Circuit Design

Parker and Stephen welcome JITX CEO and Co-founder, Dr. Duncan Haldane, to the show to discuss his company, which is a code-powered PCB design platform that aims to revolutionize circuit board design ...

28 Nov 20231h 7min

EP#405: Does ChatGPT want a cold beer?

EP#405: Does ChatGPT want a cold beer?

Parker and Stephen discuss the fact that physical limitations of shrinking process nodes are leading to new advancements in silicon interposers and enabling 2.5D packaging architectures, which is maki...

21 Nov 202345min

Populært innen Vitenskap

fastlegen
tingenes-tilstand
smart-forklart
rekommandert
sinnsyn
jss
tomprat-med-gunnar-tjomlid
rss-rekommandert
forskningno
villmarksliv
rss-paradigmepodden
fjellsportpodden
diagnose
aldring-og-helse-podden
tidlose-historier
nevropodden
dekodet-2
nordnorsk-historie
rss-nysgjerrige-norge
hva-er-greia-med